Piston Problems

Show us your pneumatic spud gun! Discuss pneumatic (compressed gas) powered potato guns and related accessories. Valve types, actuation, pipe, materials, fittings, compressors, safety, gas choices, and more.
User avatar
turbohacker
Specialist 3
Specialist 3
Posts: 392
Joined: Wed Dec 20, 2006 12:34 am

Fri Dec 22, 2006 2:21 pm

I am building my first piston gun an have had alot of troble trying to get the piston to seal aganst the barrel. :x Im using quarter inch soft rubber and a hefty spring behind the piston, any suggestins?
User avatar
mark.f
Sergeant Major 4
Sergeant Major 4
Eritrea
Posts: 3640
Joined: Sat May 06, 2006 11:18 am
Location: The Big Steezy
Has thanked: 58 times
Been thanked: 62 times
Contact:

Donating Members

Fri Dec 22, 2006 2:24 pm

How square is the surface the piston seals against to the piston? You have to have a perfectly straight cut to get a good seal.
User avatar
Bluetooth
Corporal 4
Corporal 4
Posts: 863
Joined: Tue Jun 27, 2006 7:57 am

Fri Dec 22, 2006 2:26 pm

Make sure the barrel is cut perfectly square and make sure it is very smooth start with 100 grit sandpaper and work your way up to 400 or more.
EDIT:You beat me to it.
User avatar
ProfessorAmadeus
Sergeant
Sergeant
Posts: 1046
Joined: Fri Apr 28, 2006 5:39 pm
Location: texas

Fri Dec 22, 2006 2:29 pm

Wait are you just blowing into it? If soo it probably wont seal well because humans produce only soo much Psi.
Insomniac wrote:Hey why am I a goose???? Why not somthing a little more awe inspireing, like an eagle or something? LOL
SOO CUTE!! OMG!! I COULD JUST LICK YOU!!
User avatar
turbohacker
Specialist 3
Specialist 3
Posts: 392
Joined: Wed Dec 20, 2006 12:34 am

Fri Dec 22, 2006 2:40 pm

no im not blowing into it, im filling wit a co2 tank (compressor is broken :roll: ) Ill try sanding the joint very smooth next time.
Im such an idiot, i glued the gun together without any way to work on the pison, there goes 20 bucks :x
User avatar
noname
First Sergeant 4
First Sergeant 4
Posts: 2698
Joined: Mon Apr 10, 2006 9:19 pm
Location: Bay Area, CA

Fri Dec 22, 2006 4:06 pm

Cut the barrel pipe with a pipe cutter, it leaves a smooth ridge on the end of the pipe which is perfect to seal against.
sgehring
Private 4
Private 4
Posts: 71
Joined: Tue Nov 21, 2006 11:36 pm
Location: Idaho

Sat Dec 23, 2006 3:14 am

yea pipe cutter works good or a chop saw. I used a rubber pvc cap for the diaphram. I traced the inner diameter of the barrel on it and cut it slightly oversize and then sanded the edges down to fit. It the type thats has a hose clamp on it. Its plenty thick enough and very soft. It will be slightly belled out. Put that side to where it jsut touchs the barrel and use a small equalization hole. The spring only needs to be strong enough to pop it back to shape.
The Haymaker
Private 4
Private 4
Posts: 74
Joined: Thu Sep 22, 2005 4:52 am
Location: Cowtipping, Maine
Contact:

Fri Dec 29, 2006 10:50 pm

When I first built my piston for a 2" barrel, I had problems sealing which I attributed to the piston fetching in the bore. After judicious use of prayer words, I found it was because the rubber I used for a seal was getting sucked towards the barrel and folded over as the piston came back forward. I swapped to a firmer rubber (quick cap material like you are using) and larger diameter for strength and more allowance for slight bending.

E
User avatar
ProfessorAmadeus
Sergeant
Sergeant
Posts: 1046
Joined: Fri Apr 28, 2006 5:39 pm
Location: texas

Fri Dec 29, 2006 10:56 pm

Yeah same hear. I get my piston up to 5 psi and the sealing face pops threw the barrel and releases all the pressure. It was working but it stopped. The cap that you are talking about, is it a black flexible rubber type like at lowes? If so I'll try that out.
Insomniac wrote:Hey why am I a goose???? Why not somthing a little more awe inspireing, like an eagle or something? LOL
SOO CUTE!! OMG!! I COULD JUST LICK YOU!!
The Haymaker
Private 4
Private 4
Posts: 74
Joined: Thu Sep 22, 2005 4:52 am
Location: Cowtipping, Maine
Contact:

Fri Dec 29, 2006 11:03 pm

Yeah, the one with black rubber and a hose clamp around it. I used a 3" as it was going on a 3" cap/piston. I cut it just inside of where the sides met the front, then smoothed it up with a grinder. I also used a fender washer in the center for support. I think the washer was roughly 1/4" smaller than the bore of the exhaust port. I also mounted it so the curve of the plug laid against the piston (cone shaped), figuring it'd seal better by pushing against the inner edges of the exhaust port. MUCH better than the crap I was using.
Post Reply