Shrader Valves
- crazyfreak0075
- Specialist
- Posts: 159
- Joined: Thu Aug 17, 2006 4:09 pm
Hey guys im gonna build a pnumatic soon and i was noticing that the shrader valve in this topic http://www.spudfiles.com/forums/viewtopic.php?t=3573& is different than the shrader valve sold at www.mcmaster.com.
The one in the topic has a rubber end to it to keep it in and all the one that mcmaster has is a shrader valve with an NPT end to it. Are these too valves different is one safer than the other???
The one in the topic has a rubber end to it to keep it in and all the one that mcmaster has is a shrader valve with an NPT end to it. Are these too valves different is one safer than the other???
- dippydodo03
- Specialist
- Posts: 103
- Joined: Tue Jan 23, 2007 5:11 pm
- Location: michigan
Threaded are the best because if they aren't they will blow out.
People that bash noobs can suck me!!!
-
- Staff Sergeant 3
- Posts: 1762
- Joined: Mon Mar 27, 2006 4:18 pm
- Location: United States
Oh they will...dippydodo03 wrote:Threaded are the best because if they aren't they will blow out.
- dippydodo03
- Specialist
- Posts: 103
- Joined: Tue Jan 23, 2007 5:11 pm
- Location: michigan
Hey, I'm just going off personal experiance, not trying to start anything.
People that bash noobs can suck me!!!
Mmmhmm...
I'm using a presta valve cut out of a bicycles inner tube at 200psi and its not going anywhere.
Its clamped in a 1/4" compression fitting with a steel washer though, not just slotted in a hole.
I'm using a presta valve cut out of a bicycles inner tube at 200psi and its not going anywhere.
Its clamped in a 1/4" compression fitting with a steel washer though, not just slotted in a hole.
Threaded valves are easier to put in, just drill a 3/8" hole, put the valve itself into your drill chuck and screw it in.
Rubber pull through valves always seal, because the pressure holds the valve against the inside of the pipe. I have had them at over 180 psi with no blowouts. They're easier to get, because you can just go to a bike shop and ask for all the popped tires, which they usually give you for free. Cut out the valve and pull it through a hole with pliers.
Rubber pull through valves always seal, because the pressure holds the valve against the inside of the pipe. I have had them at over 180 psi with no blowouts. They're easier to get, because you can just go to a bike shop and ask for all the popped tires, which they usually give you for free. Cut out the valve and pull it through a hole with pliers.
-
- First Sergeant 3
- Posts: 2400
- Joined: Wed Oct 18, 2006 11:12 pm
- Has thanked: 2 times
- Been thanked: 10 times
Lorem ipsum dolor sit amet, consectetur adipiscing elit. Cras nec placerat erat. Vivamus dapibus egestas nunc, at eleifend neque. Suspendisse potenti. Sed dictum lacus eu nisl pretium vehicula. Ut faucibus hendrerit nisi. Integer ultricies orci eu ultrices malesuada. Fusce id mauris risus. Suspendisse finibus ligula et nisl rutrum efficitur. Vestibulum posuere erat pellentesque ornare venenatis. Integer commodo fermentum tortor in pharetra. Proin scelerisque consectetur posuere. Vestibulum molestie augue ac nibh feugiat scelerisque. Sed aliquet a nunc in mattis.
Last edited by SpudBlaster15 on Wed Jul 14, 2021 1:27 pm, edited 1 time in total.
- experament-u2
- Specialist 4
- Posts: 469
- Joined: Tue Dec 26, 2006 11:18 pm
mine has never leaked and i take it past 60 every time i shoot
i would prefer to use a treaded one tho like they^ said can hold allot of pressure and can be made air tight easily
i would prefer to use a treaded one tho like they^ said can hold allot of pressure and can be made air tight easily
Your signature is freaking disturbing....